Wall flashing · valleys · step flashing

Roof Flashing Repair in Katy, TX

Flashing is the metal that turns water away where the roof meets a wall, a chimney or a valley. When it lifts, rusts or was caulked instead of layered, water runs inside the wall. We rebuild it the right way.

KATY, TX · HARRIS · FORT BEND · WALLER
Roof Flashing RepairKaty area homes

What is roof flashing repair?

Roof flashing repair means fixing or replacing the thin metal pieces that seal the joints of your roof. Flashing sits wherever the roof meets something else: a wall, a chimney, a skylight, a vent or the valley where two slopes meet. It is laid in layers, so each piece sheds water onto the one below, the same way shingles do.

Flashing is where most hidden leaks start. Shingles can be in great shape while a single missing piece of step flashing lets water run down inside a wall. Because the metal is tucked under shingles and siding, the damage often hides until a stain shows up on a ceiling or wall. Fixing it is skilled work, and it is a core part of the work our local roof leak specialists do every week.

How do we repair roof flashing?

Each kind of flashing has its own repair method. These are the ones we work on most in Katy:

Step flashing at walls

Step flashing is a row of small, bent metal pieces woven in with each shingle where a roof runs up a wall. Many Katy homes have a single-story section or garage roof that meets a second-story wall. We remove the shingles along that wall, replace each piece of step flashing, and make sure the siding or brick sits above it with a small gap.

Kickout flashing

Where a roof edge ends against a wall, a small piece called kickout flashing turns water into the gutter instead of down the wall. When it is missing, water pours behind the siding. Adding one is a small part with a big effect.

Valley flashing

Valleys are the channels where two slopes meet. They carry a lot of water in heavy rain. We rebuild a leaking valley with new underlayment and metal or a woven shingle valley, depending on the roof.

Counterflashing

Counterflashing covers the top edge of step flashing on brick walls and chimneys. When it pulls loose, water slips behind it. We reset it into the brick or install new counterflashing and seal it.

What are the signs of a flashing leak?

Flashing leaks often show up away from the roof itself. Watch for these eight signs:

  1. A stain on an upstairs wall or ceiling. Often right below where a lower roof meets the house.
  2. Water stains on siding or brick. Dark streaks running down from a roof edge.
  3. Swollen or rotted siding. Soft trim or siding near the bottom of a roof-to-wall joint.
  4. Thick caulk on metal joints. Heavy sealant is often a sign of a past patch over failed flashing.
  5. Rusty or bent metal. Flashing that is lifting, rusting or bent away from the wall.
  6. Leaks in wind-driven rain. Water that only shows when rain blows against one side of the house.
  7. Stains near a chimney or skylight. Both rely on flashing to stay dry.
  8. Peeling paint inside a wall. Moisture working through drywall from inside the wall cavity.

Why does roof flashing fail on Katy homes?

Flashing fails for a few common reasons, and some go back to the day the house was built:

  • Missing pieces. A step flashing piece or kickout left out during construction leaves a gap from day one.
  • Caulk instead of metal. Sealant was used where layered flashing should be. Texas heat cracks the caulk within a few years.
  • Siding set too tight. Siding pressed down onto the roof wicks water up behind the flashing.
  • Old metal reused. During a past re-roof, old bent or rusted flashing was left in place.
  • Storm damage. Wind can lift flashing away from walls. Our storm damage roof repair page covers that damage.
  • House movement. Settling foundations on Gulf Coast clay soils can shift walls slightly and open flashing joints.

What can you check safely from the ground?

You can find many flashing clues without a ladder. Try these safe checks:

  • Find where roofs meet walls. Look at each spot where a lower roof runs into a higher wall.
  • Look for kickouts. At the bottom of each roof-to-wall joint, check for a small metal piece angled into the gutter.
  • Check the siding. Look for stains, swelling or soft spots below those joints.
  • Spot heavy caulk. Use binoculars to look for thick sealant along metal edges.
  • Match inside to outside. Compare where the inside stain is to the joints on the outside wall.

What happens during our flashing repair visit?

Here is how our flashing repair visit works:

  1. We trace the leak. We check the stain, the attic and the wall area to confirm flashing is the cause.
  2. We inspect the joint. We look at the step flashing, kickout, counterflashing and siding gap.
  3. We open the area. We remove the shingles and, if needed, the bottom course of siding along the joint.
  4. We replace the flashing. We install new pieces layered the right way, with a kickout where it belongs.
  5. We close it up. We reinstall the shingles, reset the siding with a proper gap and seal the edges.
  6. We test it. We run water over the area and check inside to make sure it stays dry.

What affects the cost of roof flashing repair?

Flashing repairs vary a lot by location. These are the things that change the price most:

Roof flashing repair cost factors in Katy
FactorHow it affects the job
Length of the jointA short wall joint is quicker than a long run along a second-story wall.
Wall materialSiding can be lifted and reset. Brick may need counterflashing cut into the mortar.
Siding damageRotted siding or trim found at the joint has to be replaced too.
Roof heightJoints on second-story roofs take more setup and safety gear.
Inside wall damageWet drywall or insulation inside the wall adds work beyond the roof.
Type of flashingValleys, chimneys and skylights each need different materials and time.

We show you photos of the old flashing we remove, so you can see exactly why it failed.

When is a flashing leak urgent?

A flashing leak is urgent when water is running inside a wall or dripping from a ceiling. Water inside a wall can soak insulation and drywall and reach wiring before you see much on the surface. Call us right away, and see our emergency roof leak repair steps for what to do in the meantime.

A small, dry stain that appears only in wind-driven rain is not an emergency, but it will not fix itself. Book a visit so we can confirm the cause before storm season. If you are not sure the stain is from flashing, roof leak detection is the right first step.

Roof flashing repair FAQs

Can flashing be fixed without removing the siding?

Sometimes, but not always. To replace step flashing correctly, the bottom of the siding often has to come off and go back on. Patching with caulk alone usually fails again within a few years in Texas heat.

What is kickout flashing, and do I need it?

Kickout flashing is a small metal piece at the bottom of a roof-to-wall joint. It turns water into the gutter instead of down the wall. If your home has a roof that ends against a wall, it should have one.

Why does my wall only leak in some storms?

Wind-driven rain pushes water sideways into gaps that stay dry in calm rain. Flashing with a missing piece or a gap often leaks only when rain blows from one direction.

Can I just add more caulk?

Caulk is a short-term patch. Sun and heat crack it, and it can trap water instead of shedding it. Layered metal flashing is the lasting fix.

Does flashing need to be replaced when I get new shingles?

It should be checked every time. Good metal can sometimes stay, but bent, rusted or missing pieces should be replaced while the roof is open.

My house is brick. Is flashing different?

On brick walls, step flashing is covered by counterflashing set into the mortar joints. When that counterflashing pulls loose, we reset or replace it.

Roof flashing repair in Katy neighborhoods

Flashing problems follow the shape of the homes. Large two-story houses in Pin Oak Village and Woodcreek Reserve have long roof-to-wall joints. Complex roofs in Seven Meadows have many valleys. In Williamsburg Settlement, steep rooflines on older homes put flashing to the test. Find your neighborhood below.

Talk to our team

Stop water where the roof meets the wall.

Call Prairie Crest Roofing and our team will find and rebuild the failed flashing.

(281) 555-0164
Tap to call our team
Roof leaking in Katy?Talk to our roof leak team
Call (281) 555-0164